Home Page of Masonry Magazine

Advertise to mason contractors

Subscribe to Masonry Magazine
Sponsors of Masonry Magazine
Classified Advertising for Mason Contractors
Contact Masonry Magazine
Search Masonry Magazine
Order reprints of Masonry Magazine
News for masonry contractors
Calendar of masonry events
Links to masonry related sites
Web site of the Mason Contractors Association of America
Web site of the Mason Contractors Association of America
Sponsored topics:
Mortar & Restoration NEW!
Masonry Magazine Readership Survey

September 2007

Grout Consolidation

Getting the Air Out

Masonry Magazine

High-lift grouting typically is performed with a grout or concrete pump, as high as 24 feet in one pour.
Photo courtesy of SPEC MIX.

With the seemingly constant changes to lift heights and required consolidation in the codes, there seems to be some confusion out there as to the what, when, where, how and why concerning the consolidation of grouted masonry cells. This article will help to demystify masonry grout and vibration products, and their usage.

The quantity of new reinforced masonry construction projects has increased steadily in the United States during the past several years, led primarily by commercial projects (big-box retail, hotels and low-rise residential) and school construction. Thus, ensuring that you are well informed on the latest requirements, specifications and materials for grouting masonry walls is a marketable skill that could mean more money in your pocket from new jobs. First, let's clarify what we're talking about.

Essentially, there are two forms of reinforced masonry construction (RMC): low-lift (simultaneous masonry construction and grouting), and high-lift (grouting after masonry construction). In either form, the majority of corefill grout is used with concrete masonry units, while only a small percentage is used with clay brick construction. With the low-lift method, grout is placed as the courses are laid. The grout then can be consolidated with a "pudding stick" or a mechanical vibrator. In the high-lift method, the masonry is built to the story height, or its full height (not exceeding 12.67 feet), after which grout is poured from a hopper or pumped by mechanical means. The grout then is consolidated with a low-force vibrator. When grouting between wythes, the vibrator should be placed in the grout at points spaced 12 to 16 inches apart.

The tasks seem simple enough, so why does there seem to be so much confusion on this issue?

Masonry Magazine

A cutaway of the shaft of a mechanical vibrator.
Photo courtesy of Multiquip

Why All the Confusion?
For starters, Jeff Leonard, vice president of bulk materials for The QUIKRETE Companies, said that because of the nature of masonry grout (with a 10- to 11-inch slump) some contractors think that vibration is not necessary. "This is not the case, however, especially if there is congested rebar within a wall," he said.

Further, according to some grout suppliers and other industry experts, the code changes within national and local regulations can lead to a great deal of uncertainty among mason contractors. (More changes are, in fact, planned for the national codes, including updates for self-consolidating grout.) Additionally, the introduction of self-consolidating grout (SCG) has led some contractors to believe that vibration was no longer necessary, as if all grouts provided SCG's self-consolidating qualities. It is important to note, however, that SCGs generally only reduce the need for vibration as opposed to eliminating it entirely.

"There is a lot of confusion about grout consolidation in the industry and ACI 530 tells us that anything over a 12-inch grout lift should be consolidated and reconsolidated. This however, does not always happen," said Nick Blohowiak, a regional manager for Minnesota-based SPEC MIX. "ACI also allows for this consolidation and reconsolidation to be modified, and even potentially eliminated, if an appropriate demonstration panel is built and then tested. It is up to the architect/engineer and inspector to evaluate and enforce these codes on their projects, and all projects are different, requiring different methods to achieve success."

Further, Blohowiak noted that consolidation and reconsolidation become more critical as the lift heights increase and the amount of congestion increases in the masonry cores. And he said that if the construction is performed in hot weather, the grout has a higher propensity to rapidly loose moisture into the units as it is poured into the cavities, which leads to bridging and voids.

"A proper preconstruction evaluation of the grouting process, including analyzing the reinforcement in the cores, temperatures expected during construction, and proposed lift heights should be done as a precursor to all projects," he said. "If there is any question on how the grout will perform for the chosen method, a demonstration panel should be constructed and filled and deconstructive testing should be done to verify the success of the chosen method of grouting."

National building codes not withstanding, Blohowiak also stressed that local codes and contractor preferences for pouring methods also play vital roles in adding to the confusion and misconceptions for grouting and consolidating. But according to him, "There is no wrong way to grout in terms of lift height selection or placement method; the key to success is ensuring that quality materials go into the wall and that the cores are completely full without voids. This may require consolidation and reconsolidation if standard masonry grout is selected."

The Grout
   
Masonry Magazine
There is no wrong way to grout in terms of lift height selection or placement method; the key to success is ensuring that quality materials go into the wall and that the cores are completely full without voids.
The general consensus within the industry is that the grouting process is the most critical facet of RMC, and consolidation is the most crucial aspect of grouting. The goals are to steer clear of voids in the grout space, to ensure proper curing, and to avoid excessive debris in the grout during placement. To accomplish this, one must be fully aware of the materials and equipment required for consolidating grouted masonry cells.

Basically, there are two types of grout (fine and coarse), both of which are specified under ASTM C 476. Generally, the grout chosen for a particular job is based on the grout space dimensions, with fine grout recommended where large amounts of reinforcing steel are installed or where conduits or piping are laid.

From there, your options boil down to personal preference and availability of materials when choosing a grout supplier.

According to Blohowiak, the SPEC MIX system allows the contractor to control the mixing of grout on site with speed that rivals ready-mixed supplied grouts. SPEC MIX grouts are available in either 80-pound bags or 3,000-pound bulk bags to be used in conjunction with one of the SPEC MIX silo delivery systems. The company offers silo delivery systems that hold between one and 10 bulk bags of material to handle the smallest and largest projects. This system is gaining in popularity because of its level of quality control, speed of mixing and versatility of the silo systems, he says. "It no longer matters where the project is because bulk bags can be delivered and stockpiled ahead of the grouting schedule, and as little as a pail or as much as 40-plus yards of grout can be efficiently mixed out of one SPEC MIX silo per day," Blohowiak said.

Leonard said there are two other advantages to using pre-blended grouts (including QUIKRETE's Core-Fill Grout) with a silo system. First, he said, the mix designs that are produced and sent to the job have prior testing and back up. "If a highly fluid grout — 11-inch slump let's say — is placed in a cylinder and cured, it will probably test low due to the high water-cement ratio," he said. "Grout tested according to ASTM C 1019, sometimes referred to as the 'pin-wheel test,' allows for the highly fluid grout to bleed excess bleed-water into the block, therefore giving a resulting test that reflects the representative strength of grout placed in the wall."

Second, Leonard said, a pre-blended product gives total control to the contractor as to the timing of the grout installation. "When receiving grout via a ready-mix truck, there has to be proper coordination. The truck can come too early or late and grout dispensed in the truck is not as quick of a discharge as other pours. If there is a holdup then demurrage charges can come into play if the wait is excessive," he said.

Further, Leonard advises that grouts should be kept free of contamination. With field mixing, he said, the concern is the contaminates from contact with the earth as the material is dumped on site. In the winter, contaminates, such as salt, should be avoided. "Any contaminate can be detrimental to the ultimate strength of the finished product. Contaminates such as free salts show up in the form of efflorescence and rust shows up as a stain," he said.

Masonry Magazine

Consolidation and reconsolidation become more critical as the lift heights increase and the amount of congestion increases in the masonry cores.
Photo courtesy of QUIKRETE.

The Vibrators
According to the Brick Industry Association, grout in contact with masonry solidifies more rapidly than that in the center of the grout space. It is, therefore, important to consolidate the grout immediately after pouring to completely fill all voids. The best procedure is to have two people performing the operation jointly — one to pour the grout and the other to consolidate it. Normally, a mechanical vibrator is employed for this purpose.

Although they're not heavily marketed to mason contractors, mechanical vibrators are the standard tools used to

consolidate grout on masonry jobs. A multiplicity of manufacturers build mechanical vibrators and an assortment of attachments designed for multiple applications. Among the leading manufacturers and sellers in the United States are Multiquip Inc. (which also produces the Stow brand of vibrators and other construction equipment), Wacker Construction Equipment (headquartered in Munich, Germany), MBW Inc., Oztec Industries, and Denver Concrete Vibrator. Designs range in size from small, battery-powered units to larger tools such as generator-powered high-cycle vibrators.

A vibrator is used to ensure that the placed grout is even and free of air bubbles so that the material will maintain its strength characteristics. How the vibrators work is by spinning an off-centered weight as much as 10,000 times per minute, forcing any air pockets in the mixture to disperse. Manufacturers note that the head of the vibrator should always be lowered into the pour slowly and pulled out gradually to avoid the formation of an air pocket. The amount of time required to consolidate the grout varies depending on the mix, but it does not usually take more than 30 seconds to settle the grout sufficiently in each section.

Johnathan Cuppett, Multiquip's product manager, said that for mason contractors a flex-shaft vibrator is the most common vibration tool used. The company's MGX Series of flex-shaft vibrators are lightweight, handheld units that provide maximum flexibility by letting the user select from a variety of options best suited to the application, including power source (electric motors or gasoline engines), shaft length (eight options in lengths, from two to 21 feet), and head size (eleven sizes, from 7/8 though 2-3/4 inches in diameter).

Cuppett said that he generally sees two common errors among contractors working with vibrators: over-vibrating and not inserting the vibrator properly into the mixture. If one over-vibrates, he warned, aggregates will settle to the bottom, weakening the structure. And once you've over-vibrated, the mixture must be removed and blended again. "You want it to be an even, smooth blend throughout the entire mix," Cuppett said. And to do this, manufacturers urge users to make sure the vibrator head is completely submerged. Otherwise, "you could overheat the bearings and either cause premature wear on the head or damage the head. So you want to make sure that the head is completely submerged at all times," Cuppett said.

In contrast, Steve Payne, general manager for Denver Concrete Vibrator, which manufactures flexible shaft, pneumatic and high-cycle concrete vibrators, as well as external form vibrators, said that the common mistake made on grouting jobs is under-vibration. He also noted that it is the changes in the code and the inspectors' interpretation of those codes that often lead to some confusion with these projects. To avoid these problems, he suggested the following guidelines:

The consolidation technique in general should be five to 15 seconds at the bottom of the cell or lift, followed by pulling the vibrator up at a rate of about three inches per second. If the grout is placed in lifts, he said, it is necessary to penetrate the previous lift with the vibrator and then pull the vibrator up from there to effectively "knit" the lifts together. "Vibrator operators get a 'feel' for the job and adjust for grout consistency, et cetera, as they move along to accomplish the task properly," Payne said. "The pitch of the vibrator may actually change when the consolidation is complete, and the operator will see the surface appearance change and take on a sheen," he continued.

Payne added that if the radius of effect of the vibrator is too small for the cell, multiple insertions are required to ensure overlap of the fields of action and the elimination of voids where no vibration has taken place. The rule of thumb, he said, is that the field of action (or radius of effect) is about eight times the diameter of the vibrator head.

Conclusion
As Payne noted so well, proper internal vibration increases the bond between the grout and the rebar in RMC. It also decreases the possibility of cold joints, honeycombing, segregation and excessive air, while adding strength to the finished product. The key to ensuring that all of your projects are grouted properly is keeping abreast of the changing standards and regulations.

Leonard suggested that continuing to educate mason contractors and other construction professionals on this issue is a good place to start. "The masonry industry, particularly the MCAA, does a good job at offering doses of knowledge that are timely to changes in our industry," he said. "Like any industry that has competition — and masonry is no exception — we have to stay current with the changes and our approach to those changes. I make sure that my field (sales) managers are certified in concrete masonry testing procedures, for instance. We have to be able to assist our customers and the industry when problems, particularly with testing, occur in the field. This ends up helping in the overall process and keeps jobs moving along."






  •  
     

    www.masonrymagazine.com

    MASONRY
    ©2007 by the Mason Contractors Association of America
    All rights reserved
    33 South Roselle Road, Schaumburg, IL 60193
    Phone: 847-301-0001 or 800-536-2225 | Fax: 847-301-1110

    Web site by: Lionheart Publishing, Inc.
    506 Roswell Street, Suite 220, Marietta, GA 30060
    Phone: 770-431-0867 | Fax: 770-432-6969
    lpi@lionhrtpub.com
    www.lionhrtpub.com