A Misunderstanding or a Mortar Failure?

Words: Brian CarneyIn the construction industry, standard specifications and test methods are established to ensure that building materials are properly produced for compliance. However, too often the objective of tests and their results are misinterpreted. Field testing of job site mortar is included in a project specification for pre-construction and construction evaluation only, not to be compared to the performance parameters for a material specification. Unfortunately, in some cases, the end result is an "apples to oranges" comparison in which the final product presumably fails to meet specification.

When the subject is masonry mortars and field testing, pay close attention to the following statement printed by the American Society for Testing and Materials (ASTM): "The test results obtained under the test method (C 780) are not required to meet the minimum compressive strength values in accordance with the property specification in Specification C 270." This statement is found in the Scope of ASTM C 780 Standard Test Method for Pre-construction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry (section 1.3). Appropriately, the committee members are assigned to ASTM C 780 have included this comment in the standard's scope to help avoid any possible confusion. There is a simple reason for this assertion.

It should be no surprise that the water content of a given mortar will have a dramatic affect on the specimens compressive strength. Laboratory mortar complying with C 270 is produced with an insufficient amount of water conducive to good field working conditions or fluidity. Mortar made at the job site, which is often tested in accordance to C 780, will have additional mixing water to accommodate the absorption of the masonry unit.

After 28 days of curing, the 2"x4" cylinders cast from construction mortar at a flow (fluidity) greater than 135% will attain only 71% of the compressive strength achieved by the same mixture tested in the lab at 105% flow. In theory, then, if 1800 psi is desired for C 270 Type S mortar, job site mortar should only be expected to attain a strength of 1278 psi.

Construction mortar sampled in the field using ASTM C 780 should not be expected to obtain as high a strength as mortar prepared in the lab using ASTM C 270. This fact is commonly misunderstood which leads to problems. Occasionally, design professionals have shut down projects due to misinterpretation of field test results. Tests conducted under C 780 were intended to evaluate field mixed mortars for consistency and composition, not conformance to property requirements in C 270. Factory pre-blended mortar offers the customer accurately weighed mix designs, and the opportunity to test according to C 270. The proper field testing of pre-blended mortar would involve sampling the dry premixed mortar and running the compressive test under the requirements of C 270.
OSHA’s 2025 Top Violations: What the Numbers Reveal for Masonry and Construction
March 2026

Each year, the Occupational Safety and Health Administration (OSHA) publishes its list of the most frequently cited workplace safety standards based on federal inspection data. The purpose is simple: show employers where hazards are consistently being fou

Greg Brown
MAP Partner
Read More
Combining Modern Healthcare with Tribal Design: Nisqually Health & Wellness Center
March 2026

The Nisqually Health & Wellness Center is a project that the wonderful team here at Warfield Masonry completed in 2020. Built on the Nisqually Reservation (near Olympia, Washington), this project incorporates a variety of masonry materials into its tribal

Jake Sulya
Case Study
Read More
The Power of the STABILA Laser Technology
March 2026

In modern construction, accuracy is no longer a luxury; it is an expectation. From interior layouts to large-scale site preparation, professionals rely on tools that deliver fast, reliable, and accurate results. Among the most influential innovations of r

MAP Partner
Read More
More Than Just A Material: Why Workforce Development Matters
March 2026

I was asked by the MCAA to share my path and objectives for Masonry Promotion and Outreach that I have worked on in NC over the years. To do that, I want to take you through my path and the key industry people that it took to impacted me for a lifelong ca

Brandy Shaver Ryan Shaver
Resources
Read More