10 Tips and Tricks to Keep Masonry Looking Its Best

Words: Darcy Boyle
Photos: PROSOCO

Cleaning new masonry can be a challenge, but when done correctly, it enhances the natural beauty of brick, stone, or concrete surfaces and helps them stay in excellent condition for years. While post-construction cleaning is just a fraction of the total building cost, the visual payoff is significant. On the other hand, improper cleaning can leave permanent damage that ruins the entire look of a structure. Here are 10 essential tips to help you avoid common mistakes and keep your masonry looking clean, fresh, and professional.

1.) Safety First, Always

Before using any cleaning product, take time to read and understand the safety guidelines. Many instructions may seem obvious—wear goggles, gloves, and protective clothing—but others are critical to preventing accidents. Never mix masonry cleaners with other chemicals or bleach, as this can create toxic fumes. Always use cleaners for their intended purpose. These guidelines aren’t just suggestions—they’re based on field experience and are designed to keep you and your project safe.

2.) Test Before You Commit

Even if you’ve used a cleaner before, always test it on a small, hidden area. Every surface is different, and so are the stains. Test under conditions that match your actual cleaning day—same temperature, same dilution, same equipment. This step may seem like a delay, but it can save you from costly repairs and ensure consistent results across the entire surface.

3.) Allow Mortar Time to Cure

Patience pays off. Wait 14 to 28 days after construction to clean most masonry. This gives mortar joints time to fully cure and harden. If you clean too early, you risk eroding or damaging the joints. High-strength mortars, however, are tougher and can be cleaned earlier—within 3 to 7 days—if needed. When in doubt, test a section and consult with a product rep or field expert.

4.) Avoid Abrasive or Harsh Cleaning Methods

Sandblasting and muriatic acid might sound like fast solutions, but they often do more harm than good. Sandblasting erodes brick faces and joints, while muriatic acid can leave streaks, discoloration, and even trigger new staining reactions. These methods can permanently degrade the appearance and integrity of the surface. Stick to safer, masonry-specific alternatives.

5.) Choose Products from Trusted Manufacturers

Don’t settle for general-purpose cleaners or unknown brands. Use proprietary masonry cleaners from companies that offer technical support and stand behind their products. These cleaners are specially formulated to improve color uniformity, clean more evenly, and enhance appearance. Plus, with a reputable manufacturer, you gain access to expert advice, spec writing assistance, and jobsite troubleshooting—valuable resources that can make all the difference.

6.) Prewet Like a Pro

Before applying any cleaner, thoroughly soak the area with clean water. This critical step prevents the cleaner from being absorbed too quickly into the masonry, which could cause blotching or damage. Think of water as a buffer—it ensures the cleaner stays where it needs to work: on the surface. Continue to prewet each new section before applying more cleaner.

7.) Apply with Care and the Right Tools

Use a low-pressure sprayer (under 50 psi) or a soft masonry brush. High pressure can force the cleaner deep into the material, making it nearly impossible to rinse and potentially leading to stains or internal damage. Avoid letting the cleaner dry on the surface. If it begins to dry out too quickly, reapply a light coat to keep it active.

8.) Rinse Thoroughly and Effectively

Proper rinsing is just as important as cleaning. A quick spray from a hose won’t cut it. When outdoors, use a high-pressure rinse of at least 400 psi with a flow rate of 4–6 gallons per minute. When indoors, rinse with plenty of clean water using a soft brush or sponge. If water is limited, use a baking soda rinse (2 oz per gallon of water), allow it to dwell, then remove it with clean water. Residue left behind can lead to efflorescence, staining, or reduced surface durability.

9.) Be Cautious in Cold Weather

Masonry cleaning works best when the temperature is above 40°F. If it’s colder, chemical reactions slow down and can lead to poor results or unintentional damage. Water used for rinsing may also freeze inside the masonry, creating cracks. If you must clean during colder months, use hot water, extend dwell time slightly, and avoid letting the cleaner dry on the surface. Temporary enclosures and space heaters can help maintain a workable temperature. And remember—your warm-weather tests won’t apply in cold weather. Always test under current conditions.

10.) Get Expert Help When You Need It

You don’t have to solve every cleaning challenge on your own. Most reputable manufacturers and distributors have technical specialists who can answer questions, recommend products, and guide you through tricky situations. They’ve seen it all and can help you avoid trial-and-error mistakes. Whether it’s understanding chemical reactions, choosing the right cleaner, or adapting to weather conditions, expert support can save time, money, and frustration.

In conclusion, cleaning new masonry isn’t just about removing dirt—it’s about protecting your investment and showcasing the natural character of your building materials. With the right products, timing, and techniques, you can bring out the best in your masonry and ensure it stays beautiful for years to come.

10 Tips and Tricks to Keep Masonry Looking Its Best

About: Featured MAP Partner

American Treasure: Doak Campbell Stadium, Florida State University

Mast Climbing Work Platform Check List – Significant Seven

Youth Outreach and Education Arm Attends the Leon Works Career Fair

Work Trucks Need Hard-working Tires