Preventative Measures

Let's first take a look at some general maintenance tips for pressure washers and then we'll cover an appropriate preventative maintenance schedule for them.

General Maintenance Tips
Some general measures that you should take to protect your investment in cleaning equipment are:

• Just like a pickup truck or forklift, cleaning equipment will last longer if one person is responsible for using it.

• It is a good idea to have a preventative maintenance checklist attached to the machine in a clear plastic protective envelope ? along with a pencil ? so that operators can check off the preventive measures taken and make notes about needed maintenance. (If you don't have a checklist, call me at the phone number listed at the end of this article and I will send you a preventative maintenance checklist that you can modify to apply to any equipment.)

• Don't let the machine freeze. If cold weather is expected, fill the water-handling system with automotive antifreeze or windshield washer fluid. Make sure the fluid is through the heating coil and the hoses.

• Use Teflon thread tape on all plumbing connections when reassembling. Fix any leaks as quickly as possible.

• Keep the high-pressure water hose out of wheeled traffic or protect it from being run over.

• Filter the water going into the pump and clean the filter frequently. Water from new plumbing systems and fire hydrants probably will have contamination that may damage the water pump and valves.

• Some people have spread the belief that, if you have a hot water cleaning machine, you should run it at the end of the day without the heater on to let the coil cool off. This is not true. In fact, leaving the coil hot will cut down the internal rust because the heat will dry the coil and likely prevent rust from occurring.

Breaking it Down
Now, let's get a little more specific. Each of the four main elements of your cleaning equipment ? the engine, the water pump, the water heater (if you are getting the advantage of hot water) and the chemical feed system ? has its own preventative maintenance needs.

You probably were supplied with an engine maintenance schedule that should be followed. However, if it's gone the way of most maintenance manuals and can no longer be found, here are some general pointers:

• Change the engine oil ? using a multi-grade SAE oil ? every 100 hours.

• Change the oil filter when you change the oil. Change the fuel filter every 200 hours. Clean the air filter every 50 hours and change it at 200 hours.

• Clean the spark plugs after 50 hours and change the plugs after 200 hours.

The Engine
Try these good ideas to keep the engine working longer:

• Keep your cleaning equipment away from the area where you are spraying so that the water and chemicals are not drawn back into the air intake.

• Make sure the electrical connections to and from the battery and the grounding source are clean, tight and free of corrosion.

• Don't let water get on a hot engine.

• If you are going to store your washer for a period of time, drain the fuel from the entire system and replace the oil.

The Water Pump
Now, let's take a look at the water pump. Preventive maintenance for the water pump is pretty simple.

• Change the oil for the water pump every three months or 500 hours. Use non-detergent 30-weight oil. Non-detergent oil is available at auto parts stores.

• Most pumps have two oil level check points, a dipstick and a sight gauge. If you see the oil has turned milky, this indicates that water infiltrated the oil, usually caused by a bad oil seal or a broken ceramic piston. No matter the cause, the problem needs to be fixed and the oil changed.

• Run your washer at least once per month. This will keep the seals moist and saturated to avoid leaks.

A major enemy of water pumps is heat. If your washer does not have a water-recycling tank, you must not let it idle for more than a minute or two. When the pump is running it naturally generates heat. The flow of cold water cools the pump. However, when the pump is in idle mode the recycling water will soon become too hot to cool the pump. If no water is flowing through the pump, the possibility of this destructive process is increased and the time it takes is decreased ? it can take only seconds for the pump to overheat.

The Water-heater
The water-heating unit is very similar to an oil burner on a home furnace. It takes very little maintenance. The important thing is to make sure that the fuel tank and filter are kept clean and the burner does not get wet while it is running.

Chemicals and Cleaners
As you know, the chemicals used to clean masonry, either new or restoration work, are strong and harsh. The chemical handling systems that are built into standard pressure washers are not made to handle the kinds of chemicals mason contractors use, although some pressure washer manufacturers say their products can. Unless they make machines specifically for cleaning masonry and know the conditions of your work, they don't understand the complexity.

For almost all cleaning applications, a standard chemical handling system will work. But not for cleaning masonry. Standard pressure washers are made to handle standard conditions and chemicals. Masonry cleaning machines, like those made by Kem-O-Kleen, are made for cleaning masonry and handling masonry cleaning chemicals.

There are preventive measures that you can use with whichever acid handling system you are using.

• As a rule, do not pump masonry cleaning chemicals or powdered detergents through the water system.

• Use clean chemicals. Oftentimes reused chemical containers and drums will accumulate dirt in the bottom. If you are using a pump to transfer the chemical, keep the pump from touching the bottom of the container so you can lessen the risk of drawing dirt or other impurities.

• Flush the chemical handling system with water when finished. Also, immediately rinse any chemicals spilled on surfaces.

• Do not leave chemicals in the tank for long periods of time. They may separate or cause corrosion. Do not cover any chemical tanks or containers.

Conclusion
All of your equipment is an investment and valuable to your company. Keep your cleaning equipment in good order so the final step that you need to take at the end of a job ? cleaning your good work ? will be the shine on the apple and a source of pride to you, your masons and your clients.